Reston Epoxy Flooring Company
#1 Epoxy Flooring in Reston, VA
Reston Epoxy Flooring: Epoxy Flooring, Epoxy Countertops, and Commercial & Industrial Epoxy Flooring
#1 Epoxy Flooring in Reston, VA
Reston Epoxy Flooring: Epoxy Flooring, Epoxy Countertops, and Commercial & Industrial Epoxy Flooring
Reston Epoxy Flooring Company installs epoxy flooring, epoxy countertops, and commercial and industrial epoxy flooring across Reston, Virginia, and the Fairfax County communities around it. We are licensed and bonded, we bring 30 years of combined experience to every slab, we are veteran friendly, and financing is available.
We work in a community that was planned from the first sketch. Reston was founded on April 10, 1964 by Robert E. Simon, whose initials gave the town its name, and it grew village by village from Lake Anne outward: Hunters Woods, Tall Oaks, South Lakes, and North Point. The Reston Association maintains about 1,350 acres of open space and 55 miles of pathways, and four lakes, Anne, Audubon, Newport, and Thoreau, anchor the neighborhoods between them.
That planning shapes the housing we coat: townhome clusters with one and two car garages, single family homes on wooded lots, condominiums near the Town Center, and garden apartments. Under all of them sits concrete facing humid summers, wet springs, and freeze and thaw winters, so we grind, repair, and moisture test every slab before a coating goes down.
In March 2026 we finished a full flake garage floor in a Lake Anne townhome. The work ran from grinding the slab open and filling its cracks through moisture readings, the epoxy base, a full flake broadcast, and a clear topcoat. A tight cluster garage that once stored everything on stained concrete now parks the car, holds the bikes, and sweeps clean after weekends on the lake paths.
In November 2025 we coated a basement floor in South Lakes for a new family room. The scope covered grinding, moisture readings, a mitigation primer where the numbers ran high, and a warm gray flake finish under a satin topcoat. The lower level went from storage overflow to the room the household actually lives in, sealed against the damp that had kept it unfinished.
In August 2025 we rebuilt a commercial kitchen floor near Reston Town Center. We ground the slab, built a textured quartz system with cove base at every wall line, and phased the work across closed hours so the kitchen never lost a service. The seamless floor now washes down fast at close and holds its footing at the sinks and the pass.
Reston garages work overtime. In the townhome clusters the garage is the workshop, the bike room, the kayak store, and the car park in one tight rectangle, and in the single family neighborhoods it catches the Dulles Toll Road commute all winter, salt included.
We diamond grind the slab, repair cracks, and take moisture readings before building a high build system with a topcoat that shrugs off oil, hot tires, and road salt. Full flake is the Reston favorite: it hides the dust a wooded lot generates and gives the hardest working room in the house a finished face.
Many Reston lower levels sit half finished for years, held back by the cool, damp feel of bare concrete, especially in the older villages near the lakes. Epoxy seals the slab, stops the dust, and turns that level into a family room, a home office, a gym, or guest space that feels like the rest of the house.
Moisture decides the plan here. Ground near Lakes Anne, Audubon, Newport, and Thoreau keeps slabs honest, so we test before we coat, and where readings run high a mitigation primer goes down before any color coat touches the slab.
Metallic epoxy makes the floor the design feature of the room. Pigments swirl and settle through a clear binder as we work the coating, building rivers of color and depth that read closer to polished marble than to paint, in one seamless pour with no grout lines anywhere.
Reston picks metallic for finished basements, recreation rooms, home bars, and the condominium living spaces near the Town Center where a plain floor would undersell the room. A gloss or satin topcoat guards the design from chair legs and daily traffic.
For a flake finish we broadcast vinyl color chips into wet epoxy to full coverage, until the surface reads like speckled granite. That busy pattern forgives daily life: it hides small slab flaws, the leaf dust that drifts in from the pathways, and the marks of a garage that stores as much as it parks.
Blends run from quiet grays to warmer mixes, and we lay samples in your own light before you commit. The raised texture helps footing when rain rides in on tires, and the clear topcoat seals the whole pattern down for years of sweeping instead of scrubbing.
Our countertop work pours fresh epoxy over a sound existing counter or a new base, forming one seamless surface with stone like depth and hand shaped veining. Reston kitchens from the Lake Anne condos to the South Lakes single family homes get a full refresh this way, without demolition or weeks of waiting on stone fabrication.
Because every pour is shaped by hand, no two counters share the same movement or colors. We seal each with a topcoat rated for daily kitchen duty and leave simple care steps that keep the surface looking rich.
Quartz floors are built in layers, with colored quartz granules broadcast into the epoxy again and again until the surface turns thick and heavily textured. That texture brings natural grip, and the build stands among the toughest finishes we install in a home.
At home in Reston, quartz earns its keep in mudrooms where pathway grit lands, in laundry rooms, at pool entries, and in the garage entries that catch weather all year. It keeps footing on wet days and trades grout scrubbing for a quick pass with a mop.
When a slab has pitted, spalled, or settled, we rebuild it with a resurfacing overlay that restores a smooth, sound surface, ready to receive a coating or to serve as the finish itself. The earliest Lake Anne and Hunters Woods slabs are now sixty years in service, and plenty need exactly this rescue before epoxy enters the picture.
Repairs include chasing and filling cracks, patching spalls flush, and treating each joint the way that slab demands. Solid repair work stops Reston's freeze and thaw winters from printing through the finished floor.
The flex and warehouse buildings along Sunset Hills Road and the Dulles corridor carry forklifts, pallet jacks, and stacked goods through long weeks. We build those floors deep: full grinding and repair, a thick epoxy body, a hard wearing topcoat, and walkways and safety lanes striped right into the finish, while cutting the concrete dust that settled over stored goods.
A working kitchen needs a floor with no seams for grease to hide in and real grip under wet shoes. We build that floor with textured quartz or flake and cove base at the walls, then schedule in sections or during closed hours so Town Center and Lake Anne kitchens keep their doors open.
Industrial work starts with a walkthrough, not a catalog. We look at the chemicals in use, the heat, and the loads crossing each bay, then spec the build to match: reinforced where traffic runs heaviest, cove base sealing the wall lines, and a topcoat chosen for what actually spills there.
Retail floors do quiet selling. A metallic or flake finish under display lighting makes a showroom feel finished and current, holds up under daily foot traffic, and lets the staff reset the room with a mop instead of a scrub brush when the doors close.
We work across the whole of planned Reston: the Lake Anne village center and its clusters, Hunters Woods, Tall Oaks, South Lakes, and North Point, the condominiums and offices at Reston Town Center, and the flex buildings along Sunset Hills Road. Cluster life comes with association standards for parking, access, and work hours, and we plan around them without being asked: neighbors get notice, work areas stay tidy, and pathways stay clear. Owners here research carefully before they hire, so we answer in kind: moisture readings shown, systems explained head to head, and the full scope in writing before any work begins.
We begin with a visit to the property, where we walk the space with the owner, measure every section, study the slab, and note cracks, joints, old coatings, and moisture readings across the floor. Those findings shape a written quote that spells out the system, the scope of prep, and the working schedule in full.
When work starts, we protect the area, grind the concrete, complete repairs, and then apply primer, base, decorative or functional layers, and topcoat in sequence. We are licensed and bonded, and our 30 years of combined experience guide each of those steps on every project, in cluster garages and corridor warehouses alike.
We install professional grade, high solids resin systems that cure at the thickness they are laid, unlike thin consumer kits that shrink and wear through in a few seasons. A typical build opens with a penetrating primer for adhesion, adds a high build base for body and color, and closes with a topcoat matched to the traffic and chemicals ahead.
Sun, abrasion, and short return to service windows each call for a different topcoat, and polyaspartic and polyurethane finishes cover those cases with added stability and wear life. We are veteran friendly and financing is available, and the point of both is simple: the slab gets the system it needs, not the system a tight month allows.
A typical garage or basement here takes two to three days of work at the property, followed by cure time before vehicles park on it again. Commercial and cluster projects with access rules take a plan of their own, and the written quote carries the day by day schedule for the whole job.
That schedule states when you can walk the floor, when belongings can move back, and when vehicles can return, set around cluster parking and quiet hours where they apply. We finish with a full walkthrough on cure times and upkeep before we leave.
No two slabs quote the same, because four things move the number: the size of the floor, the condition of the concrete, the preparation it needs, and the system you choose. The ranges below reflect the professional work we install in Reston, and the site visit turns them into one exact figure for your floor.
Installed per square foot, solid color runs $4 to $7, full flake runs $5 to $9, and metallic runs $8 to $14. Moisture mitigation and extra topcoats move a job within those bands, which is why we measure the floor and read its moisture in person before quoting it.
Two car garages typically run $2,800 to $5,500, and three car garages typically run $4,500 to $8,500. Townhome cluster garages price by the same math, and the number shifts with prep more than with size alone: a slab that needs crack chasing, oil cleanup, or removal of a failed earlier coating takes longer to ready than a clean slab in good shape.
Basement epoxy floors typically run $3,000 to $7,500. Finished living areas with metallic designs land near the top of that band, while plain utility coatings land near the bottom, and lower levels near the lakes often add a moisture mitigation step to the scope.
Commercial work typically runs $6 to $12 per square foot installed. Big open warehouse floors with easy access sit near the low end of that range. Kitchens, wash areas, and industrial bays climb toward the top, because they add quartz texture, cove base, and phased work around operating hours.
From our Reston base we work across all five village areas, Lake Anne, Hunters Woods, Tall Oaks, South Lakes, and North Point, along the Reston Parkway and Dulles Toll Road corridors, and around Reston Town Center and the lake neighborhoods. Beyond Reston we serve Herndon, Vienna, Oakton, Fairfax, McLean, Tysons, Great Falls, Sterling, Ashburn, Chantilly, Centreville, and Falls Church.
We also coat garages, basements, patios, and commercial floors throughout the wider Fairfax County area along the Dulles corridor. If your community sits near Reston and is not named here, ask us anyway and we will answer plainly about whether we can serve the project well.
If the first thing you see at home or at work is stained, dusty concrete, that picture can change in days. We will visit, study the slab, walk you through the options in plain terms, and leave a written quote you can weigh in your own time.
Start with a simple conversation about your floor. Expect a straight answer on what the concrete needs, what the work involves, and how long it will take, with no pressure to decide on the spot.
Installed, solid color runs $4 to $7 per square foot, full flake $5 to $9, and metallic $8 to $14. Most two car garages land between $2,800 and $5,500 all in, and most commercial floors price between $6 and $12 per square foot. Your exact figure comes after the visit, when we have measured the floor and tested the slab.
Most garages and basements take two to three days of work at the property, then cure time before vehicles return. Grinding and repairs take the first day, the coating layers follow in sequence, and heavy cracking or high moisture can add a day. The written quote lays out the schedule day by day before work starts.
How long an epoxy floor lasts traces back to three things: the preparation under it, the thickness of the build, and the weekly wear the room takes. A floor that was ground, moisture tested, and built to full professional thickness serves years beyond a thin coat on raw concrete, and small habits stretch it further: sweep grit before it grinds in, and wipe spills before they sit.
A smooth surface can feel slick when wet, so grip gets planned into the build rather than added as an afterthought. Flake and quartz layers bring texture underfoot, and we can blend grip additives into the topcoat for garages, entries, kitchens, and pool areas. We set the texture level around how each room is actually used.
Yes, in most cases, and older concrete is part of life in the earliest villages, where slabs date to the 1960s and 1970s. We grind first, then chase and fill cracks, patch spalls, and read moisture across the slab, adding mitigation primer where the numbers demand it. When we find structural movement that repair cannot settle, we say so plainly before any coating work is quoted.
Interior floor work rarely needs design approval, but cluster rules do shape the practical side: guest parking for the work vehicle, access hours, and quiet hours for grinding. We ask about your cluster or condo rules at the visit, plan the schedule around them, and keep the work area tidy so the project is a good neighbor from start to finish.
Tell us about your floor. We read every request that comes in and respond with the next step, starting with a visit to measure the slab, take moisture readings, and talk through the right system for the space.
Prefer to talk it through first? Send the form and we will call you back at the number you give us.